SIIG CE-MT0K11-S1 Manual

SIIG Wandstøtte CE-MT0K11-S1

Læs gratis den danske manual til SIIG CE-MT0K11-S1 (8 sider) i kategorien Wandstøtte. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 25 anmeldelser. Har du et spørgsmål om SIIG CE-MT0K11-S1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Universal Tilting TV Mount - 23" to 42"

Installation Instructions

04-0676C

Important: If you have difficulty following or understanding these installation instructions,

please consult a qualified installation specialist.

Tilting Flat-Panel TV Wall Mount

Material: 2.0mm Cold Rolled Steel Plate

TV size: 23" - 42"

Tilt: 0 / +15 degrees

Max load capacity: 99lbs / 45kgs

Wall distance: 3.1" / 80mm

Bubble level included

Universal Mounting Pattern

Caution

• Prior to installation of this product, the installation instructions should be read and

completely understood. The installation instructions must be read to prevent personal

injury and property damage. Keep these installation instructions in an easily accessible

location for future reference.

• This mount contains small parts which can act as a choking hazard if swallowed.

• CAUTION: The maximum load capacity is 99lbs. Use with products exceeding the

maximum load capacity may cause serious injury. See apparatus instructions.

• The wall structure must be capable of supporting at least five (5) times the maximum load

capacity as indicated. If not, the wall must be reinforced.

• Recommended mounting surfaces: wood stud and solid-flat concrete/brick. If the

mount is to be installed on any surface other than wood studs, solid concrete or brick, use

suitable hardware (not included but commercially available).

• Do not install on a structure that is prone to vibration, movement or chance of impact.

Failure to do so could result in damage to the display and/or damage to the mounting

surface.

• Do not install near heater, fireplace, air conditioning, in direct sunlight or any other heat

producing source. Failure to do so may result in damage to the display and could

increase the risk of fire.

• Make sure no water or natural gas lines are present where the mount is to be installed.

Cutting or drilling into water or natural gas lines could cause personal injury or property

damage.

• Proper installation procedure by yourself or a qualified service technician, as outlined

in the installation instructions, must be adhered to. Failure to do so could result in

serious personal injury.

• When mounting to a wall that contains wood studs, confirm the dead center of the wood

stud prior to installation, it is recommended that the wood studs be a minimum of 16"

apart (if applicable).

• This product is intended for indoor installation/use only. Premature product failure or

serious personal injury could occur if this product is used outdoors.

• It is recommended that two people perform the installation. Injury and/or damage can

result from dropping or mishandling the display.

Tools Required

• Electronic stud finder for drywall installation

• Phillips head screw driver

• 7/16" socket and wrench

• Electric drill, 1/8" (3mm) drill bit for wood stud installation, 5/16" (8mm) masonry drill

bit for concrete/brick wall installation

Important: The Universal Tilting TV Mount - 23" to 42" is shipped with the proper installation

hardware and parts. Make sure that none of the items are missing or damaged before starting

the installation. If there are any missing and/or damaged parts, please stop the installation

and contact your place of purchase.

Produkt Specifikationer

Mærke:	SIIG
Kategori:	Wandstøtte
Model:	CE-MT0K11-S1
Bredde:	820 mm
Dybde:	78 mm
Højde:	494 mm
Vægt:	3100 g
Produktfarve:	Sort
Husmateriale:	Stål
Monteringstype:	Væg
Hældningsvinkelområde:	-15 - 0 °
Kapabilitet:	LCD/plasma
Montering interface kompatibilitet (min.):	200 x 100 mm
Montering interface kompatibilitet (maks.):	200 x 200 mm