Winegard Sensar III GS-2200 Manual

Winegard TV antenne Sensar III GS-2200

Læs gratis den danske manual til Winegard Sensar III GS-2200 (2 sider) i kategorien TV antenne. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Winegard Sensar III GS-2200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Figure 4

Figure 2

U.S. Pat. No. D355,887,

D358,365, 5,515,240 Power

supply housing design.

CAUTION: No splitters or coupler should be installed in the coax

line between the antenna and power supply.

Attach

coax here.

NOTICE: FAILURE TO PROPERLELY CONNECT

CABLES MAY RESULT IN DAMGE TO TV SET.

TO PREAMPTO TV

Figure 3

3-1/4"

#6x1/2

Screws

(2) E-Clip

(2) Pin

(2) Hex Nut

Mast Bracket

U-Bolt

Mast Clamp

Figure 1

WARNING:

INSTALLATION OF ANTENNAS NEAR POWER LINES IS DANGEROUS.

FOR YOUR SAFETY, FOLLOW THE INSTALLATION INSTRUCTIONS.

INSTALLATION

This SENSAR antenna may be installed inside or outside on any mast or

pole. DO NOT MOUNT OVER CHIMNEY OPENING.

STEP 1. Make sure "W" opening is on bottom side of antenna head, foot

embossing points down. Slide metal mounting bracket up into back bracket

on antenna and attach with pins and E-clips. See Figure 1.

STEP 2. Insert "U" bolt thru mast clamp and mast bracket and start hex

nuts onto "U" bolt. See Figure 1.

STEP 3. Slide mast thru "U" bolt and tighten hex nuts with 7/16" wrench.

Model GS-1100, VM-1100 (Non-amplified Models ONLY)

Attaching Downlead Cable

STEP 1. Attach downlead cable to F-jack on back of antenna head and

tighten securely. (Figure 4). Tape downlead to mast and run cable to TV.

STEP 2. Attach "F" connector to downlead and connect to "F" jack on TV.

Models GS-2200, VM-2200

(Amplified Models ONLY)

Attaching Downlead Cable

STEP 1. Attach downlead cable to F-

jack on back of antenna head and

tighten securely. (Figure 4) Tape

downlead to mast and run cable to

power supply location.

STEP 2. Attach "F" connector to

downlead and connect to "F" jack on

power supply marked "TO PREAMP".

See Figure 2.

STEP 3. Attach "F" connector to cable

from TV and connect to "F" jack on

power supply marked "TO TV". See

Figure 2.

STEP 4. Mount the two #6 screws

vertically 3-1/4" apart leaving screw

heads approximately 1/8" from wall.

See Figure 3.

STEP 5. Hang power supply onto

screws and plug power supply AC

power cord into receptacle.

Produkt Specifikationer

Mærke:	Winegard
Kategori:	TV antenne
Model:	Sensar III GS-2200

Har du brug for hjælp?

Hvis du har brug for hjælp til Winegard Sensar III GS-2200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

TV antenne Winegard Manualer

Winegard DS-3101 Manual

5 Juli 2025

Winegard Prostar PR-5646 Manual

5 Juli 2025

Winegard HD7082 Manual

5 Juli 2025

Winegard Playmaker Manual

27 August 2024

Winegard TRAV'LER SK-7002 Manual

27 August 2024

Winegard Sensar III GS-2200 Manual

27 August 2024

Winegard FL5500A Manual

27 August 2024

Winegard TRAV'LER SKA-733 Manual

27 August 2024

Winegard SK-3005 Manual

27 August 2024

Winegard SquareShooter SS-2000 Manual

27 August 2024

TV antenne Manualer

Nyeste TV antenne Manualer

RoadPro RPPS-24KB Manual

3 November 2025

Metra 40-FD20 Manual

5 Oktober 2025

Insignia NS-ANT700HA Manual

29 September 2025

President Himalaya WB Manual

25 September 2025

RAMI AV-530 Manual

24 September 2025

One For All 14460 Manual

13 September 2025

Axing TAA 3-00 Manual

10 September 2025

Wilson 301135 Manual

9 September 2025

Wilson 301121 Manual

8 September 2025

Wilson 301124 Manual

8 September 2025