Xantech DL95K Manual

Xantech Modtager DL95K

Læs gratis den danske manual til Xantech DL95K (8 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Xantech DL95K, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
INSTALLATION INSTRUCTIONS
DL85K
Dinky Link™ Surface Mount
Plasma\LCD\LED\CFL Friendly
IR Receiver
1
DESCRIPTION
These small IR receivers have been designed for mounting in very small
spaces. They may be mounted under shelf edges, cabinet ledges, in wall
speakers, etc. – anywhere an inconspicuous appearance is desired. The high
sensitivity of these receivers allows placement behind speaker grilles and still
receive IR commands up to 80 feet away*.
FEATURES
• Wire channel for clean installation.
• System testing red-talk-back LED.
• Includes 789-44 connecting block, power supply, and four 283D emitters
for easy system installation.
SPECIFICATIONS
• Infrared carrier frequency bandwidth: 25 - 60 kHz.
• Reception range: Up to 80 feet.*
• Reception angle: +/- 60 degrees.
• Cable requirements: See “INSTALLATION” below.
• Max. Transmission length: 1 mile using 18 gauge wire.
• Maximum current output: 100mA.
• Drives IR emitters through Xantech Connecting Blocks, Controllers, etc.
• Dimensions: 2.55” x 0.55” x 0.35” (65mm x 14mm x 9mm).
• Power requirements: +12VDC, 10mA.
* Depending on remote control output strength and ambient conditions.
MOUNTING
The IR receiver can be mounted to any flat surface, using the two-sided
adhesive tape supplied.
An additional feature is a wire channel on the rear of the surface mount IR
receiver. This will give the installer the ability to provide clean wire dressing in
any direction.
2
INSTALLATION
QUICK-START
A typical system will use an IR receiver, several emitters, and a power supply
all connected to a connecting block.
1. Connect the IR receiver to the “IR RCVR” port on the connecting
block. The ‘red’ connector is installed to the ‘red’ plug.
Note: In some extended distances, additional 3-conductor may be
required and can be connected to the terminals on the connecting
block.
2. Connect the Emitters to the connecting block. The ‘yellow’ connector
is installed to the ‘yellow’ plug.
3. Connect the power supply to the connecting block.
REMOTE ROOM APPLICATION
One application is to locate the IR receiver in a remote room. This will give the
end-user the ability to control audio/video equipment from a location where
the remote control no longer has the ability of direct line-of-sight.
The IR receiver will need the 3.5mm stereo type mini plug removed to extend
the wire run to the connecting block. A 3-terminal block can be purchased
separately to connect the IR receiver to the connecting block with a 3-
conductor inter-room cable in between.
To 120 V AC
(unswitched)
781ERGPS
789-44
Connecting Block
MAIN ROOM
A/V Receiver
DVD
Satellite Receiver
283D Emitter
12VD C
+12 VDC
GND
STATUS
IR IN
EMITTERS
IR
RCVR
789-44
CONNECTING BLOCK
®
283D Emitter
283D Emitter
(mounted on or
near cabinet in an
inconspicuous
location).
DL Series
I
R Receiver
Hand Held
Remote
IR Photodiode
Red
Talkb ack LED
3
The 3-conductor inter-room cable (24 gauge up to 200’, 22 gauge up to 600’,
20 gauge up to 2000’, 18 gauge up to 5000’), is run to the main room.
Input connections must be made as illustrated. To extend the emitter wires to
a more distant location, you may splice in 2-conductor wire, in the wire
gauges mentioned before, as needed.
While it is possible to make wired connections without the connecting block, it
is not recommended. The connecting block reduces installation time, helps to
eliminate errors, allows easy troubleshooting and permits easy system
upgrades later, if needed.
DL Series
IR Receiver
Red (or white)
Stripe
To 120 V AC
(unswitched)
781ERGPS
789-44
Connecting Block
REMOTE ROOM MAIN ROOM
Hand Hel d
Remote
3-Terminal Block (not included)
3-Conductor
Inter-room Cable
(unshielded OK)
7' Ribbon Cable
A/V Receiver
DVD
IR Photodiode
Red
Talkback L ED
Satellite Receiver
283D Emitter
12VD C
+12 VDC
GND
STATUS
IR I N
EMITTERS
IR
RCVR
789-44
CONNECTING BLOCK
®
IR OUT
+12V
GND
283D Emitter
283D Emitter

Produkt Specifikationer

Mærke: Xantech
Kategori: Modtager
Model: DL95K

Har du brug for hjælp?

Hvis du har brug for hjælp til Xantech DL95K stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Xantech Manualer

Xantech

Xantech ML95K Manual

29 August 2024
Xantech

Xantech Micro Link ML85 Manual

28 August 2024
Xantech

Xantech Dinky Link 48095D Manual

26 August 2024
Xantech

Xantech Dinky Link 48085DB Manual

26 August 2024
Xantech

Xantech Hidden Link 29195D Manual

21 Juli 2024
Xantech

Xantech Hidden Link 29185D Manual

21 Juli 2024
Xantech

Xantech DL95K Manual

16 December 2022
Xantech

Xantech HL95K Manual

16 December 2022

Modtager Manualer

Nyeste Modtager Manualer

Planet Audio

Planet Audio TR4000.1D Manual

15 Juni 2025
Planet Audio

Planet Audio PL3000.1D Manual

15 Juni 2025
Planet Audio

Planet Audio PSX18 Manual

15 Juni 2025
Planet Audio

Planet Audio MB600.2D Manual

15 Juni 2025
Planet Audio

Planet Audio AC1600.4 Manual

15 Juni 2025
Planet Audio

Planet Audio PL2400.4 Manual

15 Juni 2025
Rane

Rane Zone Power Eight Manual

14 Juni 2025
Blaupunkt

Blaupunkt Melbourne 130 Manual

14 Juni 2025
NVX

NVX NDA12001 Manual

14 Juni 2025
Denon

Denon AVC-1930 Manual

14 Juni 2025