Xantech Micro Link ML85 Manual

Xantech Modtager Micro Link ML85

Læs gratis den danske manual til Xantech Micro Link ML85 (4 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Xantech Micro Link ML85, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION INSTRUCTIONS

MODEL

ML85

Micro Link™ Peep-Hole Style

Plasma\LCD\LED\CFL Friendly

IR Receiver

DESCRIPTION

The Micro Link IR Receiver is a small peep-hole style infrared repeater

assembly. The Micro Link IR Receiver is equipped with a 7-foot cable and

a 3.5mm stereo mini plug, which is plugged directly into the “IR RCVR”

jack on the connecting block, such as the models 789-44, CB60, and 791-

44. The Micro Link IR Receiver is primarily intended for use in installations

where the connecting block is within reach of its 7-foot cable – as when

installing the Micro Link IR Receiver in a cabinet where the controlled

equipment is behind closed doors.

FEATURES

• Small size; mounts in 1/2” diameter hole. 2 inches deep (50mm).

• Quick-Connect 3.5mm Stereo Mini Plug on 7ft. cable for direct plug-in

to Xantech Connecting Blocks.

• Works in normal 3-wire mode (12VDC, IR, GND).

• Green Talkback LED for System Verification.

SPECIFICATIONS

• Infrared modulation frequency bandwidth: 30 – 60 kHz.

• IR reception range: Up to 80 feet, depending on remote control output

strength and ambient conditions.

• Reception angle: 55 degrees off axis for 50% range reduction.

• Cable requirements: 3-conductor. Use 24 gauge up to 200’, 22 gauge

up to 600’ 20 gauge up to 2000’, 18 gauge up to 5000’ – unshielded

OK.

• Max. transmission length: 1 mile using 18 gauge wire.

• Maximum current output: 100mA

• Drives IR emitters through Xantech Connecting Blocks, Controllers,

etc.

• Dimensions: 1/2” diameter x 2” deep (13mm x 50mm).

• Power requirements: +12VDC, 20mA.

INSTALLATION

QUICK-START

A typical system will use an IR receiver, several emitters, and a power

supply all connected to a connecting block. (sold separately)

1. Connect the IR receiver to the “IR RCVR” port on the connecting

block. The ‘red’ connector is installed to the ‘red’ plug.

Note: In some extended distances, additional 3-conductor may be required and can

be connected to the terminals on the connecting block.

2. Connect the Emitters to the connecting block. The ‘yellow’

connector is installed to the ‘yellow’ plug.

3. Connect the power supply to the connecting block.

4. Installation complete

MOUNTING

Drill a 1/2” hole in any surface, such as a cabinet panel. Pass the lead and

the body of the ML85 through the hole and secure from the rear with the

nut (supplied).

LOCAL SYSTEM APPLICATION

In this system a 283D Blink-IR Designer Emitter is shown connected to the

“OUT” jack. If expansion beyond two emitters is required, use an optional

Xantech 789-44, CB12, CB60, or 791-44 Connecting Block.

CABLE CONNECTIONS

ML85s may also be used where the 7-foot cable is not long enough.

Simply cut off the mini plug, strip the leads and splice them to a 3-

conductor extension cable with a terminal block or other means. Then

connect the extension cable to the 3- or 4-terminal block on the connecting

block.

ML Series

IR Receivers

To 120 VAC

(unswitched)

781ERGPS

789-44

Connecting Block

Hand Held

Remote

A/V Receiver

DVD

IR Photodiode

Talk back LED

Satellite Receiver

283D Emitter

12VDC

+12VDC

GND

STATUS

IR IN

EMITTERS

RCVR

789-44

CONNECTING BLOCK

283D Emitter

(sold separately)

3.5mm mini plug Signal Name

TIP SIGNAL

RING GROUND

SLEEVE +12VDC

The 3-conductor inter-room cable (24 gauge up to 200’, 22 gauge up to

600’, 20 gauge up to 2000’, 18 gauge up to 5000’), is run to the main room.

While it is possible to make wired connections without the connecting

block, it is not recommended. The connecting block reduces installation

time, helps to eliminate errors, allows easy troubleshooting and permits

easy system upgrades later, if needed.

PLACEMENT

The IR receiver should be located so that it is not directly facing a light

source such as lamps or displays (standard, LCD, and Plasma). When

mounted near a display, it should be flush to the display and away from

light reflections that may occur.

Produkt Specifikationer

Mærke:	Xantech
Kategori:	Modtager
Model:	Micro Link ML85

Har du brug for hjælp?

Hvis du har brug for hjælp til Xantech Micro Link ML85 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Xantech Manualer

Xantech ML95K Manual

29 August 2024

Xantech Micro Link ML85 Manual

28 August 2024

Xantech Dinky Link 48095D Manual

26 August 2024

Xantech Dinky Link 48085DB Manual

26 August 2024

Xantech Hidden Link 29195D Manual

21 Juli 2024

Xantech Hidden Link 29185D Manual

21 Juli 2024

Xantech DL95K Manual

16 December 2022

Xantech HL95K Manual

16 December 2022

Modtager Manualer

Nyeste Modtager Manualer

Planet Audio AC1200.2 Manual

15 Juni 2025

Planet Audio AC2400.4 Manual

15 Juni 2025

Planet Audio AC2600.2 Manual

15 Juni 2025

Planet Audio PL1500.1M Manual

15 Juni 2025

Ecler HSA2-400ES Manual

15 Juni 2025

Planet Audio PL4000.1D Manual

15 Juni 2025

Planet Audio MB1200.4D Manual

15 Juni 2025

Pure Acoustics AZ-2U-3240 Manual

15 Juni 2025

Ecler AURA-4B600 Manual

15 Juni 2025

Planet Audio TR3000.1D Manual

15 Juni 2025