Xantech HL95K Manual

Xantech Modtager HL95K

Læs gratis den danske manual til Xantech HL95K (8 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Xantech HL95K, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
INSTALLATION INSTRUCTIONS
HL95K
Hidden Link™ Shelf Top
Extended Range
Plasma\LCD\LED\CFL Friendly
IR Receiver
1
DESCRIPTION
The Hidden Link IR Receiver is a small shelf-top infrared repeater assembly. It
includes an IR receiver. a 789-44 Connecting Block, a Power supply, and 4
283D emitters. The Hidden Link IR Receiver is equipped with a 7-foot cable
and a 3.5mm stereo mini plug, which is plugged directly into the “IR RCVR” jack
on the 789-44. It can also be plugged into the “AUX” or “IR RCVR” jack of other
Xantech connecting blocks, such as the models CB12, CB60, and 791-44. The
Hidden Link IR Receiver is primarily intended for use in installations where the
connecting block is within reach of its 7-foot cable – as when installing the
Hidden Link IR Receiver in a cabinet where the controlled equipment is behind
closed doors.
FEATURES
• Very small package, only 2.00”L x 3.15”W x 0.70”H.
• System testing red-talk-back LED.
• Includes 789-44 Connecting Block, Power supply, and four 283D emitters
for easy system installation.
SPECIFICATIONS
• Infrared carrier frequency bandwidth: 25 – 60 kHz.
• Reception range: Up to 80 feet, depending on remote control output
strength and ambient conditions.
• Nominal reception angle: 55 degrees off axis.
• Cable requirements: See “INSTALLATION” below.
• Max. transmission length: 1 mile using 18 gauge wire.
• Maximum current output: 100mA
• Drives IR emitters through Xantech Connecting Blocks, Controllers, etc.
• Dimensions: 2.00”x3.15”x0.70” (51mm x 80mm x 18mm)
• Power requirements: +12VDC, 20mA.
2
INSTALLATION
QUICK-START
A typical system will use an IR receiver, several emitters, and a power supply
all connected to a connecting block.
1. Connect the IR receiver to the “IR RCVR” port on the connecting block.
The ‘red’ connector is installed to the ‘red’ plug.
Note: In some extended distances, additional 3-conductor may be required and can be
connected to the terminals on the connecting block.
2. Connect the Emitters to the connecting block. The ‘yellow’ connector is
installed to the ‘yellow’ plug.
3. Connect the power supply to the connecting block.
4. Installation complete
LOCAL SYSTEM APPLICATION
In this system a 286D Dual Blink-IR Designer Emitter is shown connected to
the “OUT” jack of the 789-44. A single emitter could also be used, such as the
model 282D or 283D. If expansion beyond four emitters is required, use a
Xantech 791-44 Connecting Block in place of the 789-44.
283M
Blink-IR™
Mouse Emitter
To 120 VAC
(unswitched)
781RG
Power Supply
789-44
Connecting Block
283M
Emitter
283M
Emitter
Equipment Rack
Hand Held
Remote
VCR
HL series
Hidden Link
IR Receiver
12VDC
+12VDC
GND
STATUS
IR IN
EMITTERS
IR
RCVR
789-44
CONNECTING BLOCK
®
Satellite Receiver
AV Receiver
3
CABLE CONNECTIONS
The HL series may also be used where the 7-foot cable is not long enough.
Simply cut off the mini plug, strip the leads and splice them to a 3-conductor
extension cable with a terminal block or other means. Then connect the
extension cable to the 3-terminal block on a CB12 or a 789-44 as shown in the
figure below.
3.5mm mini plug Signal Name Wire Color
TIP SIGNAL WHITE
RING GROUND BLACK
SLEEVE +12VDC RED
The 3-conductor inter-room cable (24 gauge up to 200’, 22 gauge up to 600’,
20 gauge up to 2000’, 18 gauge up to 5000’), is run to the main room.
While it is possible to make wired connections without the connecting block, it is
not recommended. The connecting block reduces installation time, helps to
eliminate errors, allows easy troubleshooting and permits easy system
upgrades later, if needed.
283M
Blink-IR™
Mouse Emitter
To 120 VAC
(unswitched)
781RG
Power Supply
789-44
Connecting Block
283M
Emitter
283M
Emitter
Equipment Rack
VCR
12VDC
+12VDC
GND
STATUS
IR IN
EMITTERS
IR
RCVR
789-44
CONNECTING BLOCK
®
Satellite Receiver
AV Receiver
HL Series IR Receiver

Produkt Specifikationer

Mærke: Xantech
Kategori: Modtager
Model: HL95K

Har du brug for hjælp?

Hvis du har brug for hjælp til Xantech HL95K stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Xantech Manualer

Xantech

Xantech ML95K Manual

29 August 2024
Xantech

Xantech Micro Link ML85 Manual

28 August 2024
Xantech

Xantech Dinky Link 48095D Manual

26 August 2024
Xantech

Xantech Dinky Link 48085DB Manual

26 August 2024
Xantech

Xantech Hidden Link 29195D Manual

21 Juli 2024
Xantech

Xantech Hidden Link 29185D Manual

21 Juli 2024
Xantech

Xantech DL95K Manual

16 December 2022
Xantech

Xantech HL95K Manual

16 December 2022

Modtager Manualer

Nyeste Modtager Manualer

Planet Audio

Planet Audio TR4000.1D Manual

15 Juni 2025
Planet Audio

Planet Audio PL3000.1D Manual

15 Juni 2025
Planet Audio

Planet Audio PSX18 Manual

15 Juni 2025
Planet Audio

Planet Audio MB600.2D Manual

15 Juni 2025
Planet Audio

Planet Audio AC1600.4 Manual

15 Juni 2025
Planet Audio

Planet Audio PL2400.4 Manual

15 Juni 2025
Rane

Rane Zone Power Eight Manual

14 Juni 2025
Blaupunkt

Blaupunkt Melbourne 130 Manual

14 Juni 2025
NVX

NVX NDA12001 Manual

14 Juni 2025
Denon

Denon AVC-1930 Manual

14 Juni 2025