Hudson Valley KBS1752803-AGB/SWH Manual

Hudson Valley Lys KBS1752803-AGB/SWH

Læs gratis den danske manual til Hudson Valley KBS1752803-AGB/SWH (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Hudson Valley KBS1752803-AGB/SWH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SPLIT

KBS1752803

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS

AFTER USE.

REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR

TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

FIXTURE INSTALLATION

1. Attach the MOUNTING PLATE (1) unto the junction box using the MOUNTING SCREWS (2). This fixture is

designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted

to the structure of the building.

2. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the

GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

3. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together

with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with

electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires

same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS

COULD RESULT IN SERIOUS INJURY OR DEATH!

5. Attach the FIXTURE ASSEMBLY (6) to the MOUNTING PLATE (1) and secure with the BOLT NUT (5).

6. Adjust the ARMS (8) and SWIVEL (9) to the desired Angle.

Screw the BULB (7) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 60 WATT TYPE G25

LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!

Restore power to the outlet at the breaker or fuse box.

ITEM DESCRIPTION PART NUMBER

1MOUNTING PLATE HDW-KBS1752803

2MOUNTING SCREW HDW-KBS1752803

3GROUND SCREW HDW-KBS1752803

4WIRE NUT HDW-KBS1752803

5BOLT NUT HDW-KBS1752803

6FIXTURE ASSEMBLY FAS-KBS1752803

7BULB NOT INLCUDED

8ARMS FAS-KBS1752803

9SWIVEL FAS-KBS1752803

10 RING RNG-KBS1752102

11 SHADE SHD-KBS1752102

FIXTURE INSTALLATION

1. Attach the MOUNTING PLATE (1) unto the junction box using the MOUNTING SCREWS (2). This fixture is

designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted

to the structure of the building.

2. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the

GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

3. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together

with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with

electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires

same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS

COULD RESULT IN SERIOUS INJURY OR DEATH!

5. Attach the FIXTURE ASSEMBLY (6) to the MOUNTING PLATE (1) and secure with the BOLT NUT (5).

6. Adjust the ARMS (8) and SWIVEL (9) to the desired Angle.

Screw the BULB (7) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 60 WATT TYPE G25

LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!

Restore power to the outlet at the breaker or fuse box.

SPLIT

KBS1752803

INSTALLATION INSTRUCTIONS

www.hvlgroup.com

ITEM DESCRIPTION PART NUMBER

1MOUNTING PLATE HDW-KBS1752803

2MOUNTING SCREW HDW-KBS1752803

3GROUND SCREW HDW-KBS1752803

4WIRE NUT HDW-KBS1752803

5BOLT NUT HDW-KBS1752803

6FIXTURE ASSEMBLY FAS-KBS1752803

7BULB NOT INLCUDED

8ARMS FAS-KBS1752803

9SWIVEL FAS-KBS1752803

SHADE SHD-KBS1752102

ATTENTION PRUDENCE

DÉBRANCHEZ L'ALIMENTATION AVANT DE REMPLIR OU DE CÂBLER LE LUMINAIRE. LISEZ

COMPLÈTEMENT TOUTES LES INSTRUCTIONS AVANT DE COMMENCER L'INSTALLATION

POUR ÉVITER LE RISQUE D'INCENDIE OU D'ÉLECTROCUTION, LE LUMINAIRE DOIT ÊTRE INSTALLÉ

CONFORMÉMENT À TOUS LES CODES ÉLECTRIQUES/DE CONSTRUCTION NATIONAUX ET LOCAUX

APPLICABLES. L'INSTALLATION ET L'ENTRETIEN DE CET APPAREIL DOIVENT ÊTRE EFFECTUÉS PAR UN

ÉLECTRICIEN AGRÉÉ OU UN TECHNICIEN CERTIFIÉ FORMÉ EN USINE.

CALIFORNIE PROP 65 : CET APPAREIL D'ÉCLAIRAGE CONTIENT DES PRODUITS CHIMIQUES CONNUS PAR

L'ÉTAT DE CALIFORNIE POUR PROVOQUER LE CANCER, DES MALADIES CONGÉNITALES ET/OU D'AUTRES

DOMMAGES À LA REPRODUCTION. LAVER LES MAINS APRÈS UTILISATION.

RETIRER LE LUMINAIRE, LES PIÈCES ET LE(S) SAC(S) DE PIÈCES DU CARTON. AVANT DE JETER LE

CARTON, VÉRIFIEZ DOUBLE POUR VOUS ASSURER QUE TOUTES LES PIÈCES SONT TROUVÉES.

INSPECTER LE LUMINAIRE AVANT L'INSTALLATION POUR TOUT DOMMAGE AU LUMINAIRE.

GRADATION : LE LUMINAIRE PEUT ÊTRE CONTRLÉ PAR UN DISPOSITIF DE GRADATION MURALE. UTILISER

UNIQUEMENT UN GRADATEUR TRIAC/ÉLECTRONIQUE. ASSUREZ-VOUS QUE LE CARTON EST MARQUÉ

POUR UNE UTILISATION AVEC UNE SOURCE DE LUMIÈRE FLUORESCENTE À INCANDESCENTE COMPACTE

UNIQUEMENT. CEUX-CI PEUVENT ÊTRE FOURNIS PAR VOTRE DISTRIBUTEUR ÉLECTRIQUE LOCAL,

CENTRE À DOMICILE OU MAGASIN DE QUINCAILLERIE.

VEUILLEZ NETTOYER UNIQUEMENT AVEC UN CHIFFON DOUX ET SEC ! N'UTILISEZ PAS DE NETTOYANTS

Produkt Specifikationer

Mærke:	Hudson Valley
Kategori:	Lys
Model:	KBS1752803-AGB/SWH

Har du brug for hjælp?

Hvis du har brug for hjælp til Hudson Valley KBS1752803-AGB/SWH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Hudson Valley Manualer

Hudson Valley Montvale 4813-AGB Manual

4 November 2024

Hudson Valley Hollis 3610-AGB Manual

4 November 2024

Hudson Valley Highland Falls 9500-AGB Manual

4 November 2024

Hudson Valley Preston 4216-HN Manual

4 November 2024

Hudson Valley Crystler 5135-AGB Manual

4 November 2024

Hudson Valley Tring PI1894501-AGB Manual

4 November 2024

Hudson Valley Crystler 5133-AGB Manual

3 November 2024

Hudson Valley Brookhaven 7222-VGL Manual

3 November 2024

Hudson Valley Mimi H711506-AGB Manual

3 November 2024

Hudson Valley Murray Hill 9280-AGB Manual

3 November 2024

Lys Manualer

Nyeste Lys Manualer

Javalo Elf JE-BLY03 Manual

19 Juni 2025

Martin MAC Aura Raven XIP Manual

19 Juni 2025

Emos ZGD070P Manual

19 Juni 2025

Tracer Flex Manual

19 Juni 2025

Tracer Ambience - Smart Corner Manual

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

18 Juni 2025