Hudson Valley Williamsburg 1057-AGB Manual

Hudson Valley Lys Williamsburg 1057-AGB

Læs gratis den danske manual til Hudson Valley Williamsburg 1057-AGB (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Hudson Valley Williamsburg 1057-AGB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FIXTURE INSTALLATION

1. Feed the wire through the STEM (6) and twist tightly onto the FIXTURE ASSEMBLY (10). Keep adding

additional stems until you desired hanging height is met.

2. Slide in CANOPY(7) onto the STEM (6), and thread the 1/4 NIPPLE (5) onto the top end of the STEM (6)

3. Pull the wire out from the junction box, and install the MOUNTING PLATE (1) onto the junction box using the

MOUNTING SCREWS (2). This fixture is designed to be mounted on standard round or octagon junction box.

The junction box must be securely mounted to the structure of the building.

4. Trim off the excess wire to a minimum 6" beyond the STEM and strip each wire 5

8".

5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the

GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together

with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with

electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same

as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD

RESULT IN SERIOUS INJURY OR DEATH!

8. Push the wires back into the junction box. Lift up the CANOPY (7) up to the ceiling, and secure it with the

HEADLESS SCREW (8) by using supplied ALLEN KEY TOOLING (9) .

9. Attach the SHADE (12) to the FIXTURE ASSEMBLY (10) and secure with the TOP FINIAL (11) .

10. Screw the BULB (13) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 9 WATT LAMP. DO

NOT EXCEED THE RECOMMENDED WATTAGE!

11. Lift the DIFFUSER (14) up onto the fixture and secure using the BOTTOM FINIAL (15) .

12. Restore power to the outlet at the breaker or fuse box.

WILLIAMSBURG

1057

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS

AFTER USE.

·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR

TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

Questions? We're here to help!

ITEM DESCRIPTION PART NUMBER

1MOUNTING PLATE HDW-001046

2MOUNTING SCREW HDW-001046

3GROUND SCREW HDW-001046

4WIRE NUT HDW-001046

51/4 NIPPLE HDW-001046

6STEM STM-104603,06,12,18

7CANOPY CAS-001046

8HEADLESS SCREW CAS-001046

9ALLEN KEY TOOLING MIS-001046

10 FIXTURE ASSEMBLY FAS-001057

11 TOP FINIAL FIN-001002-T

12 SHADE SHD-001057

13 A15 LED BULB NOT INCLUDED

14 DIFFUSER DIF-001057

15 BOTTOM FINIAL FIN-001002-B

Produkt Specifikationer

Mærke:	Hudson Valley
Kategori:	Lys
Model:	Williamsburg 1057-AGB

Har du brug for hjælp?

Hvis du har brug for hjælp til Hudson Valley Williamsburg 1057-AGB stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Hudson Valley Manualer

Hudson Valley Glimmer 5351-AGB Manual

7 December 2025

Hudson Valley Verona Beach 7614 Manual

7 December 2025

Hudson Valley Southold 3938-AGB Manual

7 December 2025

Hudson Valley Lina BKO252-AGB Manual

6 December 2025

Hudson Valley Times Square 3806-AGB Manual

30 Juni 2025

Hudson Valley Times Square 3810-AGB Manual

30 Juni 2025

Hudson Valley Amboy 1504-AGB Manual

29 Juni 2025

Hudson Valley Collins 2938-PN Manual

29 Juni 2025

Hudson Valley Woodlawn 1728 Manual

28 Juni 2025

Hudson Valley Ovid 1920-AGB Manual

27 Juni 2025

Lys Manualer

Nyeste Lys Manualer

Vaxcel CH55606 Manual

25 December 2025

Vaxcel H0198 Manual

25 December 2025

Neolium X8 Manual

25 December 2025

Biltema 27-000 Manual

25 December 2025

Vaxcel P0260 Manual

24 December 2025

Vaxcel PD5024 Manual

24 December 2025

Vaxcel CR-VLU002 Manual

24 December 2025

Biltema 48-540 Manual

24 December 2025

Vaxcel W0375 Manual

24 December 2025

Vaxcel C0279 Manual

24 December 2025