PAC C2R-VW2 Manual


Læs gratis den danske manual til PAC C2R-VW2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7 anmeldelser. Har du et spørgsmål om PAC C2R-VW2, eller vil du spørge andre brugere om produktet?

Side 1/2
Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
03-16-10
Radio Replacement Interface
with Nav Outputs for select
Volkswagen CANbus Vehicles With
or Without Premium Audio Systems
C2R-VW2
1. Vehicles with or without a factory amplier: Connect the aftermarket radio’s
front and rear speaker wires to the 16 pin plug.
2. The accessory output wire is located on the 11 pin CAN INTERFACE harness
- connect this wire to the radio’s
accessory wire. The accessory wire
supplies +12v, 1 amp max when key is
in the accessory or ignition position (see
g. 1: If more current is needed).
3. 11 pin plug (to CAN INTERFACE):
White/Green - Steering Wheel Control (SWC) output.1.
Green - Connect this wire to the radio’s reverse input wire only.2.
Orange/White - Connect this wire to the radio’s Illumination input wire only.3.
Violet/White - Connect this wire to the radio’s VSS input wire only.4.
Red/White - Connect this wire to the radio’s parking brake input wire only. 5.
Please Note: The parking brake wire will output a neg (-) trigger at all times until the vehicle is moving at a
speed of approximately 3 mph or faster.
Note: Do not connect these wires to any circuit other than the aftermarket radio’s wire harness.
4. 11 pin plug (to SWC INTERFACE):
This is a quick connection to a radio specic SWC interface. No additional connections are necessary other than radio
control connections. Plug the radio specic SWC interface in to this connector and program the radio specic SWC
interface for version 2. Do not cut the loops. Refer to the SWC interface instruction manual for the radio specic control
function programming order.
Fig. 1
(using a SPDT relay)
85 86
30
87
87a
Ground
High Current 12v
(Fused)
12v Acc.
From
Interface
New High
Current Output
Diode 1N4005
or equivelant
23456
78
1011
Accessory Output
+12volts 1amp max.
9 1
23456
78
101
9 1
SWC Interface.
Program for Version 2
Radio Specific Steering
Wheel Control Interface
(Sold Separately)
Program SWC
Interface for Version 2.
CAN INTERFACE
Navigation outputs and
Amplifier Remote Input
See Chart for wire color
descriptions.
Radio Connections. See aside
Chart for color description.
Yellow Battery +12v
Black Ground
Blue Amp Turn On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Radio Connection Chart:
(Read the Installation Notes before making
connections to the provided radio harness)
CAN Interface Connection Chart:
Red Acc. Output (1 amp)
Red / White P.B. Output (-)
Purple / White VSS Output (Pulse)
Orange / White Illum. Output (+)
Green Reverse Output (+)
White / Green SWC Output
Page 1


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: C2R-VW2

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC C2R-VW2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer