PAC IR-X Manual
PAC
Ikke kategoriseret
IR-X
Læs gratis den danske manual til PAC IR-X (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om PAC IR-X, eller vil du spørge andre brugere om produktet?
Side 1/1

Pacic Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
Pacic Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
IR-X Infrared Remote Repeater Installation Instructions 8-15-03
Control remote mounted / hidden video players and stereos using the units IR remote*.
* note: The IR remote being used must use a 40kHz or 56kHz carrier
frequency. Consult with equipment manufacture to determine the carrier
frequency. Check website for known units that do not work.
Special Features:
• Easy 2 wire hook up
• Extra long plug-in wire for remote IR
LED
• Red LED ashes for conrmation of
wireless remote operation (red LED
will be dim when ashing)
• Small and easy to mount
• 40kHz and 56kHz operation
Black receiver
(Round dimple must
face wireless remote)
Clear emitter on 1/8" plug
(round dimple must face device)
1. Connect Red wire to 12 volts accessory (switched power)
2. Connect Black wire is vehicle ground (negative)
3. Mount IR receiver (on the end of the short black wire) with the
round dome side facing out where it is in range / sight of the
remote control.
4. Mount IR LED (on the end of black wire with 1/8” plug) in front
of the unit/s to be controlled. The IR LED is directional, so
make sure the dimple on the side of the clear IR LED is facing
the unit being controlled. It can be taped to the front of the
unit or mounted in a location that can be seen by two or more
units to be controlled.
5. By leaving the brown wire of the IR-X disconnected and
insulated, it will transmit at a 40kHz IR signal, which is used
for most applications.
-or-
When the brown wire is connected to vehicle ground
(negative) the IR-X will transmit at a 56kHz IR signal which
is used in fewer applications. Ground the brown wire if only
the control response is slower than normal or is intermittent.
Installation Instructions
IR-X Infrared Remote Repeater Installation Instructions 8-15-03
Control remote mounted / hidden video players and stereos using the units IR remote*.
* note: The IR remote being used must use a 40kHz or 56kHz carrier
frequency. Consult with equipment manufacture to determine the carrier
frequency. Check website for known units that do not work.
Special Features:
• Easy 2 wire hook up
• Extra long plug-in wire for remote IR
LED
• Red LED ashes for conrmation of
wireless remote operation (red LED
will be dim when ashing)
• Small and easy to mount
• 40kHz and 56kHz operation
Black receiver
(Round dimple must
face wireless remote)
Clear emitter on 1/8" plug
(round dimple must face device)
1. Connect Red wire to 12 volts accessory (switched power)
2. Connect Black wire is vehicle ground (negative)
3. Mount IR receiver (on the end of the short black wire) with the
round dome side facing out where it is in range / sight of the
remote control.
4. Mount IR LED (on the end of black wire with 1/8” plug) in front
of the unit/s to be controlled. The IR LED is directional, so
make sure the dimple on the side of the clear IR LED is facing
the unit being controlled. It can be taped to the front of the
unit or mounted in a location that can be seen by two or more
units to be controlled.
5. By leaving the brown wire of the IR-X disconnected and
insulated, it will transmit at a 40kHz IR signal, which is used
for most applications.
-or-
When the brown wire is connected to vehicle ground
(negative) the IR-X will transmit at a 56kHz IR signal which
is used in fewer applications. Ground the brown wire if only
the control response is slower than normal or is intermittent.
Installation Instructions
Produkt Specifikationer
Mærke: | PAC |
Kategori: | Ikke kategoriseret |
Model: | IR-X |
Har du brug for hjælp?
Hvis du har brug for hjælp til PAC IR-X stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret PAC Manualer
11 Juli 2025
11 Juli 2025
10 Juli 2025
10 Juli 2025
30 Juni 2025
10 Marts 2025
19 Februar 2025
19 Februar 2025
19 Februar 2025
19 Februar 2025
Ikke kategoriseret Manualer
- Constructa
- Airlux
- APsystems
- Chipolino
- Jahnke
- Benavent
- Belden
- Roxio
- IsoAcoustics
- NWS
- SVS
- DriverGenius
- Intel
- Bang And Olufsen
- Omiindustriies
Nyeste Ikke kategoriseret Manualer
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025