PAC OnStar OS-4 Manual

PAC Ikke kategoriseret OnStar OS-4

Læs gratis den danske manual til PAC OnStar OS-4 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 67 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 34 anmeldelser. Har du et spørgsmål om PAC OnStar OS-4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com Page 1

10-29-10

The OS-4 is a plug and play interface that allows the replacement of a General Motors GMLAN factory radio. The OS-4 will

maintain operation of the OnStar® system in vehicles with Bose® audio systems, amplied audio systems and also audio

systems without external ampliers . The OS-4 has on board switching that allow audio from the OnStar® system to play

through the two front factory speakers. This interface retains all warning chimes, audible turn signal indicators, Bluetooth

and the Vehicle Rear Parking Assist System (if equipped). The factory XM radio tuner can be controlled from the Steering

Wheel Controls (SWC) or Rear Seat Entertainment (RSE) Controls. RSE headphone jacks will also remain active and are

designed for use with dual zone radios and the factory installed XM tuner. If the overhead LCD is present the IR headphone

system will also be active.

General Motors OnStar®

Interface for GMLAN Vehicles With or

Without Factory Amplied Audio Systems

*These instructions only support revision 1.2.3.8 or higher of the OS-4

1. The OS-4 will retain the use of the factory installed XM receiver. Factory SWC or RSE Controls must be present for use of this feature.

2. You may use this interface if the vehicle does not have OnStar® but you need to interface with the Bose® amplier

3. This interface will work in amplied or non-amplied audio systems.

4. This interface retains the 5.1 audio system in equipped Cadillac vehicles.

5. Built in Smart Mute Circuitry will play OnStar® through the front speakers and allow the RSE audio jacks to continue playing the audio

source selected by the RSE Controls.

• OnStar® active LED and Ignition on LED.

• New radio will operate with the vehicle RAP (Retained Accessory Power) system.

• Provides +12v RAP circuit, Illumination, Vehicle Speed Sensor (VSS) Output, Parking brake, and Reverse trigger outputs.

• OnStar® Volume control via factory steering wheel audio controls or a push-button switch.

• Safety chime audio level is controlled through the Driver Information Center (DIC).

• RSE Controls will play the aftermarket radios dual zone source or the factory XM tuner if serviced.

• Overhead RSE LCD is usable as well as factory IR headphone system and Rear Auxiliary Input Jacks (use PAC Part # GMRVD).

• Steering wheel radio controls can be retained to control new radio by using the SWI-X, ECL2, JACK or PS.

J1850

Class 2

VPW

Class 2

J1850

1 0 0 0 1 0 1 0 0 1 0 0 1 0 1 01 1 1 1 1 1 1 0

1 1 1 11 0 1 0 0 0 0 1 0 1 01 1 1 0 0 1 01 0

Arbitration

EOD

CRC

1 0 0 0 1 0 1 0 0 1 0 0 1 0 1 01 1 1 1 1 1 1 0

1 1 1 11 0 1 0 0 0 0 1 0 1 01 1 1 0 0 1 01 0

Class 2

J1850

Notes

Installation

OS-4

OS-GMLAN29

OS-NAV

XM R

XM L

Connect to SWC

Interface. Program

for Version 2.

OS-RADPWRAUDIO

• Aftermarket radio connections are made at the 20-pin OS-RADPWRAUDIO connector. A

detailed description of these wires is on the next page. PLEASE NOTE: The audio inputs

of the OS-4 are designed to be used with the aftermarket head unit’s speaker output

ONLY (60W X 4 MAX). If you are using an additional aftermarket amplier, you must

make your speaker connections AFTER the OS-4 at the Vehicle Connections plug.

If you want to retain OnStar while using an aftermarket amp, a seperate speaker

must be hooked up to the front left output of the OS-4.

• If the vehicle has Rear Seat Audio Controls and the XM tuner is serviced plug the 8 pin

XM Audio output cable into the OS-4. The RCA cables will feed the XM audio into the

aftermarket radios AUX input (if available). The XM RCA cables are not necessary for

Rear Seat Audio but will allow the headunit to play the XM audio through the cabin.

• Factory installed audio options such as Bose, Harman Kardon or Pioneer ampliers

will determine the 16-pin OS-GMLAN29 connection. If the vehicle has a factory installed

amplier use the Factory Amplier Audio location. If a factory installed amplier is not

present use the Non-Amplied Factory Audio location.

• The OS-NAV connector has VSS, Reverse and Parking Brake outputs as well as the

OnStar push button volume adjustment input.

• If SWC buttons are present and retained using a radio specic SWC interface use the

provided plug. No other connections or splices are necessary.

• The CMX retains all factory warning and safety chimes. If the vehicle chimes when the

radio is removed the CMX is not needed.

• The Mute loop (if not cut) will turn the ACC. output off when an OnStar or Bluetooth call

is made or received. If the aftermarket radio has a mute input cut this loop and connect

the outer brown wire to the mute input.

Vehicle Connections

Navigation Connections

SWC Interface

Connections

Upgraded Radio Connections

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com Page 2

10-29-10

Connecting to and Using OnStar

Connecting the OS-4 to an aftermarket radio

SWC Output Connector

Press and

Hold for

1.5 seconds

to Activate

Onstar Voice

Recognizition or

Bluetooth Phone

Services

Raises and

Lowers Onstar

the Audio

Level While

Onstar is

Active

(7 positions)

Activate

Onstar Voice

Recognizition

Services

Connect to

Onstar

Personal

Calling

Setvices

Onstar

Emergency

Services

Ends Current

Onstar Call

or Rejects

Incoming

Bluetooth or

OnStar Call

SRCE

• To activate Bluetooth Services (if present) and OnStar Services if Bluetooth is not present press and

hold the Speak SWC button for 1.5 seconds. Pressing the circled phone button on the OnStar touch

pad will only activate OnStar Services.

• Pressing the SWC Vol+ or Vol- during an OnStar/Bluetooth connection will raise and lower the

OnStar or Bluetooth audio level.

• Pressing the down arrow SWC button or circled phone button on the OnStar touch pad during an

OnStar or Bluetooth call will end the current OnStar connection. The down arrow will also reject

incoming OnStar or Bluetooth calls.

• OnStar Personal calling and Emergency services can be activated by the buttons on the mirror.

OnStar Level Control for Vehicles without SWC Buttons

• If SWC buttons are not present a SPST switch can be used to control the

OnStar audio level during an OnStar connection.

• Using the provided Green/White wire, connect the non-terminated end to one

side of a SPST normally open momentary switch (not included).

• The terminated end will go into the OS-NAV connector position X (see picture

above).

• The other side of the SPST switch will be connected ground.

• When OnStar is active pressing the switch will raise the audio level 7 times

before returning to the original level.

1324

Green/White wire

SPST N.O. switch (not included)

Wire insertion side view

(OS-NAV 24-pin connector) VSS

(purpl e/white)

Parking

Brake

(red/white)

Reverse

(green)

O.S.

Level Switch

(green/white)

1 Green/White OnStar Level Control

2 N.C.

3 N.C.

4 N.C.

5 N.C.

6 N.C.

7 N.C.

8 Purple/White Vehicle Speed Sensor Output

9 N.C.

10 N.C.

11 N.C.

12 N.C.

13 N.C.

14 N.C.

15 N.C.

16 N.C.

17 Green Reverse Light Output

18 Red/White Parking Brake Output

19 N.C.

20-24 N.C.

1 White FL+ Speaker Input

2 Grey FR+ Speaker Input

3 N.C.

4 N.C.

5 Black Ground

6 Yellow Battery

7 Brown Mute Sense Input

8 Purple RR+ Speaker Input

9 Green RL+ Speaker Input

10 Brown Mute Output (-)

11 White/Black FL- Speaker Input

12 Grey/Black FR- Speaker Input

13 Red RAP Output

14 Burgundy Chime+

15 Orange Illumination Output (+)

16 Blue/White Amp On Input

17 White/Green SWC Output

18 Purple/Black RR- Speaker Input

19 Green/Black RL- Speaker Input

20 Black Chime -

OS-NAV

(Wire side view)

OS-RADPWRAUDIO

(Wire side view)

• The OS-4 provides a SWC output connector attached to the

OS-RADPWRAUDIO harness. For ease of installation, all necessary

connections for a SWI-X, ECL2, JACK, or PS have made for you.

• When using this SWC output connector the radio specic SWC interface

must be programmed for version 2 (refer to SWC interface programming

instructions for exact programming sequence).

• Both loops should also remain in tact.

• During steering wheel button assignment programming each button

should be pressed and held for 1 second after the SWC interface LED

goes out with the exception of the Speak button.

• The speak button should be pressed for less than 1 second and

released.

• Pressing the Speak button for longer than 1.5 SEC will activate OnStar.

From SWC

Buttons

From OnStar Touch Pad

Connect to SWC

Interface. Program

for Version 2.

Connect to Radio

Specific SWC

Interface

Using the CMX

• The provided CMX will play all safety/warning

chimes and turn signal/hazard light tones in

vehicles that do not play these chimes/tones when

the factory installed radio is removed.

• When the radio is removed - if factory chimes still

play the CMX is not needed. The CMX cable (2-pin

connector attached to the OS-RADPWRAUDIO

interface harness) should be tied up as it is not

used for any other connections.

• To adjust the level of the warning and safety

chimes refer to the vehicles owner manual for

Driver Information Center (DIC) settings. Not all

vehicles have a DIC. If the DIC is not available the

chime level is not adjustable.

Center and Sub Connections

Center

SUB

• Some Cadillac vehicles are

equipped with a Dolby Surround

Sound Amplied Audio System. The

ampliers 5.1 mode is enabled when

the RSE system is off and OnStar is

not active. If the aftermarket radio

has a dedicated center channel

and or sub output connect it to the

provided cable as labeled. Refer to

the aftermarket radios owner manual

for surround sound settings and

adjustments.

• If the aftermarket radio to be

installed does not have a dedicated

center channel or sub output do not

use this cable. To ensure best sound

performance channel summing is

not recommended. Use this cable

according to the outputs that are

available.

• This cable can also be used for

factory reverse camera retention if

available and if center channel and

or sub connections are not needed

(see Notes section of this manual).

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	OnStar OS-4

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC OnStar OS-4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech MIC-3811 Manual

30 Juli 2025

Intermatic EI230W Manual

30 Juli 2025

Rockboard LED Light V2 Manual

30 Juli 2025

Advantech USB-5817 Manual

30 Juli 2025

Electro Harmonix 9DC-100 Manual

30 Juli 2025

Advantech UTC-515H Manual

30 Juli 2025

Extron MGP 641 xi 5K Manual

30 Juli 2025

Festo EMME-AS-80-M-LS-AMB Manual

30 Juli 2025

Tiptop Audio Octogain Manual

30 Juli 2025

Artec SE-ADL Manual

30 Juli 2025