PAC RP4-HD11 Manual

PAC Ikke kategoriseret RP4-HD11

Læs gratis den danske manual til PAC RP4-HD11 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om PAC RP4-HD11, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
RP4-HD11
Radio Replacement & Steering Wheel Control Interface
for Honda Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacic Accessory Corporation
www.pac-audio.com
Rev. 042314
C
Page 1
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the
vehicle (see next page for setting chart).
2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless you wish
to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always be restored to default
settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
3. Vehicles equipped with factory navigation must follow the installation tech brief listed at www.pac-audio.com under the RP4-HD11 product
page.
4. Vehicles equipped with a 7” touchscreen: Once the factory head unit has been removed you will no longer be able to set the clock or date
on the factory display as this is derived from the factory head unit. The date on the screen can be permanently removed by disconnecting
the batttery to clear the screen’s memory. In order to set the clock you will need to disconnect the vehicles battery at 1:00 as this is the time
the screen defaults to once it has been reset.
5. The LED will ash whenever a SWC button is pressed.
Interface Connector Vehicle Connector SWC Connector
SWC Connection
See above chart for
different radio type
connections
Acc On/
Programming
LED
Programming
Button
Wiring SWC Connection
Red / White Parking Brake
Output (-)
Purple / White Vehicle Speed
Output
Red Accessory Output
(1 amp)
Orange / White Illumination Output
(+)
Green Reverse Output (+)
White/Green SWC Analog Input
Yellow Battery +12v
Black Ground
Orange Dimmer
Orange/White Illumination
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Blu/Yel Kenwwod, Newer
JVC
3.5mm Jack Alpine, JVC,
Clarion, Fusion,
Pioneer, Sony,
Boyo, Dual,
Lightning Audio,
Visteon or Advent
The RP4-HD11 interface allows the replacement of a factory radio in select Honda vehicles with MSCAN databus radios. Using this
interface will retain factory features such as steering wheel controls (SWC), the factory amplier and the ability to set the factory clock
when the original radio is removed. Use of this interface also allows you to program two radio functions to each SWC button by using
short press long press dual command functionality. The RP4-HD11 also provides data bus driven outputs such as accessory power,
vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.
Aftermarket Radio Connections
See above chart for wire color
description.
Cut for Non-Amplied systems
Vehicle Connections
RP4-HD11
Radio Replacement & Steering Wheel Control Interface
for Honda Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacic Accessory Corporation
www.pac-audio.com
C
Rev. 042314
Page 2
Default Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always
be restored to default settings by pressing and releasing the program button on the side of the interface once and waiting 7
seconds for the LED to ash 4 times.
Installation Steps
Default SWC Button Assignments
Alpine JVC Kenwood Clarion Pionee
r
Sony Fusion
V
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Track + Track +
Track - Track - Track - Track - Search - Track - Track - Track -
V
oice/Mute Mute Mute Mute Mute Mute Mute Mute
Phone Answe
Receive Receive Answer Send Answer Call Answer/End Audio
Phone End End Reject Voice End End Reject/Source Powe
r
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface
into the vehicle.
2. Make all connections as described in the chart on page 1. If there is a Premium Audio system present: Connect the RCA inputs to the
aftermarket radios pre-amp output. The audio level will vary depending on the new radios pre-amp output voltage (2-4 volts is recommended).
If there is not a Premium Audio system present: Cut the RCA inputs off and connect the aftermarket radios speaker outputs to the
remaining wire according to the chart on page 1.
3. If the vehicle is equipped with a factory subwoofer plug the RCA cables connected to the 8 pin plug into the Subwoofer or Non-Fading output
of the aftermarket radio.
4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input).
5. If you wish to reassign functions to the SWC follow the programming instructions on the next page.
IMPORTANT! If you wish to use the Voice, Answer and End buttons you must hardwire them into the RP4-HD11. The wire you
need to connect into can be found by removing the plastic panels surrounding the steering wheel column and accessing the
connector which houses the wire (Fig. 1). Once you have located the connector you must connect into the wire located in pin
3 (Fig. 2). Wire colors are normally Blue in the Civic & Yellow in the CRV but may vary by vehicle. Connect to the RP4-HD11
interface connector as shown in Fig. 3.
SWC Plug Pin 3
8
16 9
1
Connect wire in Pin 3 to the
white/green wire in pin 5
of the RP Interface plug
Fig. 1 Fig. 2 Fig. 3
1
2
3
4
5
6
7
8
9
0
Alpine Pioneer/Other Sony FusionJVC Kenwood Clarion
1 2 3 4 7 8 9
Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon
SET RADIO SELECT SWITCH

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: RP4-HD11

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RP4-HD11 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech

Advantech MIC-3811 Manual

30 Juli 2025
Intermatic

Intermatic EI230W Manual

30 Juli 2025
Rockboard

Rockboard LED Light V2 Manual

30 Juli 2025
Advantech

Advantech USB-5817 Manual

30 Juli 2025
Electro Harmonix

Electro Harmonix 9DC-100 Manual

30 Juli 2025
Advantech

Advantech UTC-515H Manual

30 Juli 2025
Extron

Extron MGP 641 xi 5K Manual

30 Juli 2025
Festo

Festo EMME-AS-80-M-LS-AMB Manual

30 Juli 2025
Tiptop Audio

Tiptop Audio Octogain Manual

30 Juli 2025
Artec

Artec SE-ADL Manual

30 Juli 2025