Rane MP 44 Manual

Rane Blander MP 44

Læs gratis den danske manual til Rane MP 44 (9 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Rane MP 44, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

Manual-1

MP 44

DJ MIXER

OPERATORS MANUAL

QUICK START

If you have used just about any DJ mixer on the planet, you will instantly feel at home using the MP 44. Extra care was

taken to ensure that controls are where you expect them to be, and operate as you expect them to.

The MP 44 has some unique features not found on other DJ mixers. It is important that you read at least this portion of

the manual so that you get the maximum benefit from these unique features. As you refer through the rest of this manual (as

you should to get the most of it), front panel controls are on the left side of each page, rear panels are on the right.

Club Managers Section

High performance Master Limiter affects both House and Booth signals. This control is located on the rear panel and

screw driver adjust to prevent tampering. The Limiter is a safety net designed to protect ears and equipment.

Automatic Emergency Page Input provides a means to automatically interrupting all program material and broadcast

emergency messages at a pre set level. The EMERGENCY PAGE level is set independent of HOUSE- and BOOTH

LEVEL LEVEL control settings. The EMERGENCY PAGE control is a recessed, screw driver adjusted control

located on the rear panel to prevent tampering after installation. See page Manual-6 for more details.

Remote DC Master Level Control Port provides a means to control the level of the MASTER mix from a remote

location. The range of control is 0 dB to –40 dB. Applications include “gain riding” DJs, setting a comfortable listening

level from a remote location and reducing the maximum available gain. To use the optional VR 1 Remote Control,

simply connect like labeled pins together. Shielded wire is recommended. See page Manual-7 for more details.

DJ Features Section

High performance Master Limiter affects both House and Booth signals. The Limiter is a safety net designed to protect

ears and equipment. Under normal operating conditions, the LIMIT indicator should only flash occasionally. If you are

running gains high enough to cause hard limiting, faders and tone controls will not respond as expected. For example, if

you run signal levels 10 dB over the Limit threshold, you must turn signal levels down 10 dB before you hear a reduc-

tion in level. See page Manual-5 for more details.

3-band Tone Controls with full cut (off to +6 dB) on each of the four Input Buses. You know what to do with this!

FlexFX™ assignment allows any combination of the four Input Buses to be processed by the FlexFX Loop, regardless of

A-side, B-side or Post crossfader assignment! See page Manual-3 for details

WARNING: Do not operate this unit without the line cord earth ground connected. To do so may increase the risk of

electric shock and increase line cord conducted emissions.

WEAR PART

This product contains the following wear part subject to the ninety (90) day

warranty period described on page Warranty-1: (1) Active Crossover Assembly.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

To reduce the risk of electrical shock, do not open the unit. No user

serviceable parts inside. Refer servicing to qualied service personnel.

e symbols shown below are internationally accepted symbols that warn

of potential hazards with electrical products.

is symbol indicates that a dangerous voltage

constituting a risk of electric shock is present within

this unit.

is symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying this unit.

WARNING

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A ground-

ing-type plug has two blades and a third grounding prong. e wide blade or third prong is provided for your safety. If the provided plug does not

t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord and plug from being walked on or pinched particularly at plugs, convenience receptacles, and the point where it exits from

the apparatus.

11. Only use attachments and accessories specied by Rane.

12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply

cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

15. e plug on the power cord is the AC mains disconnect device and must remain readily operable. To completely disconnect this apparatus from

the AC mains, disconnect the power supply cord plug from the AC receptacle.

16. is apparatus shall be connected to a mains socket outlet with a protective earthing connection.

17. When permanently connected, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in the electri-

cal installation of the building.

18. If rackmounting, provide adequate ventilation. Equipment may be located above or below this apparatus, but some equipment (like large power

ampliers) may cause an unacceptable amount of hum or may generate too much heat and degrade the performance of this apparatus.

19. is apparatus may be installed in an industry standard equipment rack. Use screws through all mounting holes to provide the best support.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping

or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus.

NOTE: is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. ese

limits are designed to provide reasonable protection against harmful interference in a residential installation. is equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.