Rane MQ 15/30 Manual

Rane Blander MQ 15/30

Læs gratis den danske manual til Rane MQ 15/30 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Rane MQ 15/30, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

OPERATING / SERVICE MANUAL

MQ 15/30

GRAPHIC EQUALIZERS

QUICK START

Reading this section is a lot like eating spinach. Once you’re through, you can have dessert. So read this spinach, then

devour your MQ dessert.

Hook-up is intuitive. Just follow the silkscreened instructions on the rear of the unit. All three inputs are wired in

parallel (they do not sum); and all three outputs are wired in parallel. Use any ONE input and any or all outputs. Using

the MQ 15/MQ 30 in an Insert Loop of a mixer is extremely easy. Simply connect them together using a single stereo

cable (1/4" TRS) between the mixer’s Insert Loop and the PATCH I/O jack. This jack is wired for the tip=send,

ring=return convention used by many mixer manufacturers. CAUTION: USE EITHER THE PATCH I/O OR ANY OF

THE INPUT AND OUTPUT CONNECTORS — DO NOT USE BOTH AT THE SAME TIME.

Anyone familiar with other graphic equalizers finds the MQ 15/MQ 30 just as familiar. One word of caution: the

boost/cut RANGE switch drastically changes the impact of a given filter. BE CAREFUL.

Setting the IN and OUT GAIN controls to the same physical positions gives unity gain through the equalizer. That is,

moving both slider handles together (keeping them aligned) always maintains overall unity gain from input to output.

Many strange gain structure conditions may be handled with these controls. FOR BEST NOISE PERFORMANCE

ALWAYS POSITION BOTH CONTROLS AS FAR TOWARD THE TOP OF. THE UNIT AS POSSIBLE WITHOUT

LIGHTING THE OL INDICATORS. See the Operating Instructions on the back page for more information, Most

applications require only a few dB of boost or cut. Start with the RANGE switch in the 6dB position and increase to

12dB only if necessary. Setting curves is as easy as it is on all Rane graphics thanks to our unique interpolating constant-

Q circuitry. For more information on setting up your curves correctly, again, see the back page.

NEVER CONNECT ANYTHING EXCEPT AN APPROVED RANE POWER SUPPLY TO THE RED THING

THAT LOOKS LIKE A TELEPHONE JACK ON THE REAR OF THE UNIT. This is an AC input and requires

special attention if you do not have a power supply EXACTLY like the one originally packed with your unit. See the full

explanation of the power supply requirements elsewhere in this manual.

SYSTEM CONNECTION

When first connecting the MQ 15 to other components, LEAVE THE POWER SUPPLY FOR LAST. This gives you a

chance to make mistakes and correct them without damaging your fragile speakers, ears and nerves.

INPUTS. All three inputs are wired in parallel and are actively balanced (true instrumentation amplifiers). Each works

equally well. Choose strictly from a favorite hardware point-of-view, there will be no performance trade-offs. The wiring

convention adheres to American, British and International standards of pin 2 “+”, or tip being hot, pin 3 “–”, or ring being return,

and pin 1, COMMON GND, or sleeve being signal ground. Unbalanced operation involves using only pin 2 “+”, or tip as

signal and pin 1 COMMON GND, or sleeve as ground. It is not necessary to short any terminals or pins to any others. Due

to the true instrumentation nature of the inputs, there is no gain reduction if pin 3, or –,

is left open; however, if pin 3 gets

shorted, it won’t hurt anything either. Use pin 1, the shell, or the COMMON GND point on the barrier strip for shield

ground. (See Rane Note 110 for further information).

OUTPUTS. The outputs mimic the inputs. True balanced output interconnection only requires the use of pin 2 “+”, or tip,

and pin 3 “–”, or ring for signal transmission. It does not require pin 1, or signal ground. The signal exists differentially

between the two balanced leads; ground is not involved. Ground is used only for shielding. Again, have a look at Rane Note

110 for more detail.

(continued on next page)...

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	MQ 15/30

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MQ 15/30 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Audac M2 Manual

16 Oktober 2025

Proel ATMP480Z6XL Manual

14 Oktober 2025

TOA M-124FX-EB Manual

10 Oktober 2025

Audiophony MYA8C Manual

6 Oktober 2025

Audiophony Digital-3 Manual

6 Oktober 2025

Audiophony MYA5D Manual

5 Oktober 2025

Proel MQ16USB Manual

4 Oktober 2025

Rolls Mini-Mix VI MX28 Manual

3 Oktober 2025

Rolls RM65B Manual

3 Oktober 2025

Rolls PM60 Manual

3 Oktober 2025