Salus KL08RF Manual

Salus Smart hjem KL08RF

Læs gratis den danske manual til Salus KL08RF (4 sider) i kategorien Smart hjem. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Salus KL08RF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

ZigBee network wireless wiring centre (8 zones),

230 V AC

Model: KL08RF

Manual

Introduction 1. Fuse

Wiring centre description

2. Power Supply

3. Thermostat grouping status

4. Network Status diode

5. Pair button

6. Reset button

10RF (optional)RX

7. Delay jumper

8. INT/EXT antenna jumper

9. NC/NO actuators jumper

Technical Information

Product Compliance

Safety Information

This product complies with the essential requirements and other relevant provisions of Directives: EMC

2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. The full text of the EU Declaration

of Conformity is available at the following internet address: www.saluslegal.com.

Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect your device

before cleaning it with a dry cloth. This accessory must be tted by a competent person, and installation must

comply with the guidance, standards and regulations applicable to the city, country or state where the product

is installed. Failure to comply with the relevant standards could lead to prosecution.

This function is only available in Oine mode (together with CO10RF coordinator)

- it means MASTER thermostats will aect to SLAVE thermostats within specic group,

which is possible only when thermostats are paired with one KL08RF wiring centre

(optional + KL04RF) and have been assigned to gr. 1 or gr. 2.

How it works: If all thermostats of a given group will operate in automatic mode, then each of the thermostats

in a given group will work in the same way as the MASTER of this group. For example, if the MASTER thermostat

of Group 1 according to it’s programmed schedule maintains a comfort mode - all SLAVE type thermostats from

Group 1 will also maintain the comfort mode (the temperature is set individually for every thermostat). Similarly,

if the MASTER thermostat is set to Party or Holiday mode - SLAVE thermostats in his group will also work in

these modes.

The mains fuse is located under the housing cover, at the main terminals and protects the wiring centre and

devices powered by it. Use cartridge fuse-type 5 x 20 mm - nominal burn rate 12 A. To remove the fuse, lift

the socket with a at screwdriver and pull out the fuse.

- (LED is steady lit) - it means wiring centre is added to the ZigBee network and paired with CO10RF

or UGE600

- Checking the address of the wiring centre in the Zigbee network. To check the address of the

wiring centre in the ZigBee network (when using more than one) press the Pair button.

The wiring centre number is indicated by the number of LEDs at the zones:

LED diode statuses:

Functions of the Pair button:

- The wiring centre reset

(this function is described in detail on the second page of the manual).

- It is used to refresh the data, after moving jumpers 7,8 or 9.

The Reset button does not remove the wiring centre from the ZigBee network.

- (LED diode is blinking) - it means wiring centre is not connected to the network, but it is ready

for pairing with the coordinator (CO10RF) of the ZigBee network or the Internet gateway (UGE600)

Power supply for wiring centre is 230V ~, 50Hz.

Features of the installation:

• three-wire, with PE protective conductor,

• made in accordance with applicable regulations.

tional, wireless device control module that can be used Addi

example - when we can’t use cable between the KL08RF - for

ng centre and the boiler.wiri

Boiler o delay time.

There is an option to connect the 08RFA external antenna to the wiring centre.

If you use an additional antenna, place the jumper in the EXT position.

Select the type of the thermoelectric actuator connected to the wiring centre:

NC – actuator normally closed

NO – actuator normally opened

The KL08RF wireless wiring centre is a part of the iT600RF system. In combination with the wireless thermostats

from iT600RF series, KL08RF provides comfortable and reliable heating control. It is equipped with the control

outputs for the pump and boiler and has been designed to work with NC or NO actuators.

In Oine mode, communication with the wireless thermostats from iT600RF series must be done through

the CO10RF co-ordinating unit, which is in the package together with the wiring centre. To work in Online mode

(via the SALUS Smart Home app) KL08RF must be connected to the Internet gateway UGE600. In one ZigBee

network (Online or Oine) up to 9 KL08RF wiring centres can be connected. KL08RF increases ZigBee network

range.

1 2 5 7

11 1217 13 14 15 16

8 9 1063 4

1. Cartridge fuse 5 x 20 mm 12 A

2. Power Supply

3. Thermostat grouping status

4. Network Status diode

5. Pair button

6. Reset button

7. Delay jumper

8. INT/EXT antenna jumper

9. NC/NO actuators jumper

10. ZigBee network coordinator

11. Terminals for actuators

12. Pump control output

13. Boiler control output

14. CO terminal

15. Dew point sensor input (humidistat)

16. Serial connector for the KL04RF extension

17. External antenna connector

15 sec

Jumper position change must be refreshed in the memory by pressing the Reset

button (short press).

Note: Within one group there may be only one MASTER thermostat (programmable) and the rest

must be SLAVE thermostats (non-programmable).

Note: Fuse replacement should be done when the wiring centre is disconnected from power supply

230 V AC.

Note: Pump (Pump output) and boiler (Boiler output) always starts 3 minutes after

receiving the heating signal from any thermostats paired with wiring centre. Pump

stops after 3 minutes, when the last thermostat stops sending demand for heat,

while the heat source (Boiler) will turn o after the time set with the jumper.

Jumper position change must be refreshed in the memory by pressing the Reset

button (short press).

Jumper position change must be refreshed in the memory by pressing the Reset

button (short press).

The grouping function is optional - thermostats do not have to be grouped, they can operate

independently.

Address 9 is indicated by lighting up 8 LEDs of all the zones and the Network

Status LED.

230 V AC

Adress 1

Adress 2

Adress 7

Power Supply 230 V AC 50 Hz

Max load 3 A

Inputs CO terminal

Dew point sensor (humidistat)

Outputs Pump control

Boiler control

Terminals for actuators

Radio frequency ZigBee 2,4 GHz

Dimensions [mm] 355x83x67

Note: Don’t use CO10RF coordinator

with UGE600 simultaneously!

CO10RF UGE600

I 2017

T: +44 (0) 1226 323961

E: sales@salus-tech.com

Head Oﬃce:

SALUS Controls plc

SALUS House

Dodworth Business Park South,

Whinby Road, Dodworth,

Barnsley S75 3SP, UK.

www.salus-controls.com

SALUS Controls is a member of the Computime Group.

Maintaining a policy of continuous product development SALUS Controls plc reserve the right

to change speciﬁcation, design and materials of products listed in this brochure without prior notice.

Produkt Specifikationer

Mærke:	Salus
Kategori:	Smart hjem
Model:	KL08RF

Har du brug for hjælp?

Hvis du har brug for hjælp til Salus KL08RF stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Smart hjem Salus Manualer

1 Oktober 2025

1 Oktober 2025

23 Juli 2025

23 Juli 2025

22 Juli 2025

Salus TRV28RFM Manual

22 Juli 2025

22 Juli 2025

22 Juli 2025

22 Juli 2025

19 September 2024

Smart hjem Manualer

Nyeste Smart hjem Manualer

Aqara Smart Wall Switch Manual

7 November 2025

Aqara Smart Wall Switch H1 Manual

3 November 2025

Aqara Wall Outlet H2 Manual

2 November 2025

Kidde 60WLDR-W-CA Manual

2 November 2025

Aqara Wireless Mini Switch T1 Manual

2 November 2025

Acer Connect M4 Manual

31 Oktober 2025

19 Oktober 2025

18 Oktober 2025

17 Oktober 2025

10 Oktober 2025