SoundTube SA502 Manual

SoundTube Modtager SA502

Læs gratis den danske manual til SoundTube SA502 (4 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om SoundTube SA502, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Install Instructions For:

SA502

1.435.647.9555

800.647.TUBE

www.soundtube.com

Faceplate

Faceplate screws (4)

Front Rear

SA502

SA502 amplifier

Four-pin Euroblock

Mounting bracket

Two-pin jumper block

Three-pin

Euroblock (3)

Three-pin Euroblock (3)

Six-pin jumper block

Box Contents

1- Amplifier (Input Voltage 30-32VDC)

(UL 60065 compliant)

1- Stereo RCA to mini adapter

1- Power adaptor: Input 100VAC-240VAC, 50/60 Hz

Output 30-32VDC, 3.75A

2- Four-pin Euroblock connectors

3- Three-pin Euroblock connectors

1- Mounting bracket

Avis

Les produits SoundTube doit être installé par un installateur professionnel audio/contractuer.

Pour plus de sûreté et pour des performances audio optimales, l'installateur doit suivre toutes

les instructions émises par SoundTube.

Warning

SoundTube products must be installed by ofessional audio installer/contracto For safety a pr r.

and for optimum audio performance, installer must follow all directions issued by SoundTube.

1. Unpack amplifier.

Note: Follow steps 2-5 if

using the mounting adapter.

If not skip to step 6.

2. Attach mounting bracket

to a secure pole or surface

using screws or metal

strapping.

7b. In mono mode, the left

and right inputs are

combined internally and

fed to both channels of the

amp. The left and right

channels both output the

summed signal.

7a. In stereo mode, the left

and right channels remain

separate. The amp operates

as a normal stereo amp.

6. Select stereo, bridged or

mono mode with the

included jumper.

3. To attach mounting

bracket, remove all faceplate

screws from one side. Lift

faceplate and set aside.

4. Slide mounting bracket

into groove on bottom of

amplifer enclosure.

8b. Bridged: connect single

pair of speaker wire to the

center + and - terminals of 4

pin Euroblock. DO NOT use

outside terminals.

8a. Stereo and Mono:

connect speaker wires to 4

pin Euroblock.

7c. In bridged mode, the

amp becomes a mono block

amp with just one input

(left), and one output. The

bridged amp is capable of

90w in to 4 ohms.

Install Instructions For:

SA502

STEREO

Left line in

Right line in

Amp

(left)

Amp

(right)

SA502

Left line in

Right line in

Amp

(left)

Amp

(right)

MONO

SA502

Left line in Amp

(left)

Amp

(right)

BRIDGED

STEREO or MONO

9. Connect speaker

Euroblock to the SA502.

5. Replace faceplate and

screws.

Produkt Specifikationer

Mærke:	SoundTube
Kategori:	Modtager
Model:	SA502

Har du brug for hjælp?

Hvis du har brug for hjælp til SoundTube SA502 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager SoundTube Manualer

SoundTube STNet Switch II Manual

28 Januar 2025

SoundTube WLL-RX1p-II Manual

28 Januar 2025

SoundTube WLL-TR-1p-II Manual

28 Januar 2025

SoundTube SA502 Manual

28 Januar 2025

SoundTube SB335 Manual

28 Januar 2025

SoundTube MA501T Manual

28 Januar 2025

SoundTube IPD-Hub 2 DSP Manual

28 Januar 2025

SoundTube MCA7004t Manual

28 Januar 2025

SoundTube SA202-II Manual

28 Januar 2025

SoundTube MCA2004t Manual

28 Januar 2025

Modtager Manualer

Nyeste Modtager Manualer

Planet Audio PSX36 Manual

17 Juni 2025

Planet Audio PL2500.1M Manual

17 Juni 2025

MB Quart NA2-400.2RC Manual

17 Juni 2025

MB Quart NA2-400.1 Manual

17 Juni 2025

DS18 GEN-X G8400.4D Manual

17 Juni 2025

Hifonics Zeus Expansion ZXR750/1E Manual

17 Juni 2025

Futaba R7206 SB Manual

16 Juni 2025

DS18 FRP-3.5K Manual

16 Juni 2025

DS18 SMD-300.4AB Manual

16 Juni 2025

DS18 SMD-3000.1D Manual

16 Juni 2025