SoundTube WLL-RX1p-II Manual

SoundTube Modtager WLL-RX1p-II

Læs gratis den danske manual til SoundTube WLL-RX1p-II (4 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om SoundTube WLL-RX1p-II, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1.855.663.5600 | mseaudio.com | soundtube.com

Front Rear

Transmitter Box Contents

1- WLL-TX1 wireless transmitter

1- Power supply

Output: 5VDC 1.2A

2- Half rack mount adapters

2- Antenna

TX unit- Transmitter TX unit- Transmitter

RX unit- Receiver/Amp RX unit- Receiver/Amp

TX unit- Transmitter

RX unit- Receiver/Amp

Antenna (4)

Receiver Box Contents

1- WLL-RX1p wireless receiver/amp unit

1- Power supply

Output: 32VDC 3.75A

2- Half rack mount adapters

2- Antenna

2- Two-pin Euro-block connectors

FCC ID: XCO-HSWLLT IC:7756A-HSWLLT

Avis

Les produits SoundTube doit être installé par un installateur professionnel audio/contractuer.

Pour plus de sûreté et pour des performances audio optimales, l'installateur doit suivre toutes

les instructions émises par SoundTube.

Warning

SoundTube products must be installed by a professional audio installer/contractor. For safety

and for optimum audio performance, installer must follow all directions issued by SoundTube.

-II

WLL-TR-1p-II

Install Instructions For:

WLL-TR-1p-II (WLL-TX1-II transmitter and WLL-RX1p-II receiver/amp).

1. Remove unit from box.

8. For best results, Transmitter and

Receiver antennas should face the

same direction (either vertically or

horizontally).

7. Set INPUT sensitivity switch at

0 dB for normal use. If using a

high output source, set the switch

to -6dB.

6. Set RF power switch. Two

options are available, High (H) and

Low (L). The High setting is

recommended for maximum

distance. The low setting is for

installations where 2 or more

TX-1’s are on the same channel

within 60-70 ft of each other.

5. Set input switch to match the

desired input source.

2. Determine location for

placement of WLL-TX1-II. The

WLL-TX1-II may be installed in an

equipment rack (half rack adapter

required) or on a shelf.

-II

4. If desired, the variable LINE

OUT mini jack can be connected

to an external device such as an

ADA hearing assistance system.

3. Connect desired input source to

rear panel. You may use balanced

(1/4” TRS) connectors, unbalanced

mini or USB. Multiple sources may

be connected but only the source

selected on the input switch (step

5) will be sent to the transmitter.

When connecting through the USB

input do not connect an input to

the balanced or line in.

11. After installation of

WLL-RX1p-II unit(s), apply power

to WLL-TX1-II. Adjust front panel

gain knob as needed. The gain

control will adjust the level of both

the input audio and the LINE OUT

feed.

10. On front panel, select transmit

channel 1, 2 or 3. NOTE: the

WLL-RX1p-II unit(s) must be set on

the same channel.

9. Connect power supply to DC IN

5V connector.

12. Done!

(The LED on the front panel will

be red when power is applied to

the TX unit. It will turn blue when

the TX unit is in communication

with the RX).

WLL-TX1-II Install Instructions

-II

Installation Notes: 2a: an installation that puts the WLL-TX1-II in line-of-sight with the WLL-RX1P-II will provide the best results. 2b: Do not install transmitter

more than 230 feet (70 meters line of site or 50 meters indoors) from the desired receiver location(s). 3a: If using the USB input, the WLL-TX1-II will appear as

an audio device on your computer’s control panel.

WLL-TR-1p-II

Install Instructions For:

WLL-TR-1p-II (WLL-TX1-II transmitter and WLL-RX1p-II receiver/amp).