WyreStorm RXV-70-4K-ARC Manual

WyreStorm AV forlænger RXV-70-4K-ARC

Læs gratis den danske manual til WyreStorm RXV-70-4K-ARC (4 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12 anmeldelser. Har du et spørgsmål om WyreStorm RXV-70-4K-ARC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

4K HDR HDMI-Over-HDBaseT Receiver

with ARC & Audio Return

RXV-70-4K-ARC Quickstart Guide

RXV-70-H2 v2 Quickstart Guide | 190319

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x RXV-70-4K-ARC Receiver

1x IR Emitter

1x IR Receiver

1x 3-pin Terminal Block

2x Mounting Brackets

1x Quickstart Guide (this document)

HDMI

RXV-70-4K-ARC Receiver

MX-1616-H2XC

4K HDR HDMI Display

Audio

Return

Channel Digital

Audio

Digital Audio

KEY

Digital Audio

HDBaseT / Ethernet

HDMI

HDBaseT Cat6/6a/7

Note: HDMI or S/PDIF I/O

available for audio return

4K HLG Source

4K HDR Source HDMI

HDMI

AV Receiver

RXV-70-H2 v2 Quickstart Guide | 190319

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated VGA, HDMI, and DP cables

due to the complexity of these connector types. Using pre-terminated

cables will ensure that these connections are accurate and will not interfere

with the performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received by the NetworkHD

system. Other 3rd party emitters and receivers can be used; however, these

devices must operate in the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a NetworkHD system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within the

port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

The RXV-70-4K-ARC uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary from

device to device. Refer to the documentation for the connected device for pin

functionally to ensure that the correct connections can be made.

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Audio Wiring

This receiver contains audio connections for S/PDIF TOSLINK (Digital Optical) input. Due to the nature of optical cables we recombined using pre-terminated

cables for this connection.