PAC RadioPRO 3 RP3-GM11 Manual

PAC Ikke kategoriseret RadioPRO 3 RP3-GM11

Læs gratis den danske manual til PAC RadioPRO 3 RP3-GM11 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om PAC RadioPRO 3 RP3-GM11, eller vil du spørge andre brugere om produktet?

Side 1/2
RP3-GM11
Radio Replacement Interface for General Motors Vehicles
Pacifi c Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacifi c Accessory Corporation
www.pac-audio.com
Rev. 120513
P ifi A C ti
3
3
3
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
The RP3-GM11 interface allows the replacement of a factory radio in select General Motors vehicles with Class II radios. Using
this interface will retain factory features such as Warning Chimes and BOSE® amplifi er (Standard or Premium) when the original
radio is removed. The RP3-GM11 provides data bus driven outputs such as retained accessory power (RAP), vehicle speed
sensor (VSS), illumination, reverse trigger and parking brake. The RP3-GM11 also provides a secondary output for adding an
optional PAC Steering Wheel Control (SWC) retention interface (SWI-RC, SWI-PS, SWI-JACK, SWI-ECL2 or SWI-X). Rear Seat
Controls (RSC) if equipped will also be retained with the SWI interface.
1. When used in Non-BOSE® applications simply cut off the RCA connectors and connect the remaining wires to the aftermarket
radios high level speaker outputs.
2. For BOSE® systems, the recommended line level input is between 2-4 volts from the aftermarket radio.
3. RSC buttons that are identical to the SWC will mimic the SWC one for one
4. To prevent over driven audio when installing the interface into a vehicle with a BOSE® system, and the aftermarket radio does
not have low level outputs, then an LOC (part # SOEM-4 or LP3-4) is recommended to match the input voltage or you can create
an audio attenuation circuit (see diagram 2 below for audio attenuation wiring).
5. Use the 4 position selector switch located on the side of the interface to select the best chime output volume for your specifi c
installation .
Red / White Parking Brake
Output (-)*
Purple / White Vehicle Speed
Output*
Blue / White Amp Turn On Input
Red Accessory Output
(10 amp)
Orange / White Illumination Output
(+)*
Green Reverse Output (+)*
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector
Audio Attenuation Circuit for RP3-GM11
One channel shown
*Not all radios will have these
connections. Please insulate
these wires when not used.
Diagram 1
Chime Volume Adjustment
Cut for Non-Bose systems
Aftermarket Radio
Connections
To Vehicle
Connector
Connect to SWC
Interface. Program
for Version 2.
To optional SWC interface
Acc On
LED


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: RadioPRO 3 RP3-GM11

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RadioPRO 3 RP3-GM11 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer