Pro1 R251S Manual

Pro1 Termostat R251S

Læs gratis den danske manual til Pro1 R251S (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Pro1 R251S, eller vil du spørge andre brugere om produktet?

Side 1/2
R251S
Installation Manual
Pro1 Technologies
P.O. Box 3377
Springeld, MO 65804
Toll Free : 888-776-1427
Web: www.pro1iaq.com
Hours of Operation: M-F 9AM - 6PM Eastern
Table of Contents
Sensor Mounting & Setup
Wiring
Resistance Chart
Specications & Warranty
Page
A trained, experienced
technician must install this
product.
Carefully read these
instructions. You could damage
this product or cause a
hazardous condition if you fail
to follow these instructions.
Una version en espanol de este
manual se puede descargar en
la pagina web de la compania.
Rev. 1809
Wall Mount
Mounting Locations
3-4
5-6
7
8
2
Sensor Mounting & Setup Sensor Mounting & Setup
Connecting to a Wired Sensor Capable Thermostat
The remote sensor should be mounted or placed approximately 4 to
5 feet above the oor. Select an area with average temperature and
good air circulation.
• Close to hot or cold air ducts
That are in direct sunlight
With an outside wall behind the thermostat
• In areas that do not require conditioning
Where there are dead spots or drafts (in
corners or behind doors)
Where appliances could radiate heat.
• Near or on hot appliances.
Remote Sensor Locations
Do not mount or place remote
sensors in these locations:
Do not operate the cooling
system if the outdoor
temperature is below 50˚F
(10˚ C) to prevent possible
compressor damage.
Caution: Equipment
Damage Hazard
The range between the remote sensor and the wired sensing master
thermostat is up to 300 feet. The remote sensor should be installed
using 18 AWG thermostat wire.
Wired Range
Remove the cover of the remote sensor
Mount subbase to the wall
Inside view of
subbase or the
remote sensor
Loosen the terminal block screws. Insert wires, then retighten
terminal block screws.
Non-Flammable
Insulation
Terminal Blocks
Connect the remote sensor to the S terminal blocks on the Wired
Sensor Capable Thermostat.
S1
S2
Place non-ammable insulation into wall opening to prevent
drafts.
Note: Refer to your Wired Sensor Capable
Thermostat manual for setup.
U.S. Registered Trademark. Patents pending
Copyright 2017 All Rights Reserved.
NO
NO
NO
YES


Produkt Specifikationer

Mærke: Pro1
Kategori: Termostat
Model: R251S

Har du brug for hjælp?

Hvis du har brug for hjælp til Pro1 R251S stil et spørgsmål nedenfor, og andre brugere vil svare dig




Termostat Pro1 Manualer

Pro1

Pro1 T501ML2 Manual

21 August 2025
Pro1

Pro1 T721 Manual

20 August 2025
Pro1

Pro1 T731WO Manual

20 August 2025
Pro1

Pro1 R251S Manual

20 August 2025
Pro1

Pro1 T805 Manual

20 August 2025
Pro1

Pro1 T701i Manual

20 August 2025
Pro1

Pro1 T721i Manual

20 August 2025
Pro1

Pro1 E219 Manual

20 August 2025
Pro1

Pro1 T701 Manual

20 August 2025
Pro1

Pro1 T755S Manual

20 August 2025

Termostat Manualer

Nyeste Termostat Manualer

Cepra

Cepra 4100 Manual

17 November 2025
Vimar

Vimar 30811.B Manual

9 November 2025
Vimar

Vimar 02974.N Manual

9 November 2025
Bosch

Bosch BCC110 Manual

8 November 2025
Vimar

Vimar 30811.G Manual

8 November 2025
Warmup

Warmup 7iE Matter Manual

7 November 2025
Vimar

Vimar 30811.C Manual

31 Oktober 2025
Delta Dore

Delta Dore Tybox 137 Manual

17 Oktober 2025