Rane HC 6 Manual

Rane Blander HC 6

Læs gratis den danske manual til Rane HC 6 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Rane HC 6, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

HC 6

HEADPHONE CONSOLE

OPERATORS MANUAL

QUICK START

Okay, you’re in a hurry. Well this section’s just for you. It explains enough of the HC 6’s workings to keep you out of

trouble. It allows operation without reading the whole manual. Please read at least this section to ensure reasonable opera-

tion of the unit.

The HC 6 operates from either a common stereo or mono source, or from individual stereo sources. For a common

stereo source, plug the left and right input plugs into the respective MASTER INPUTS jacks. The Inputs accept balanced

or unbalanced sources. Just plug them in. This source is now routed to each of the six input Channels to drive all Outputs.

For a single mono source feeding all headphones, connect it to one of the MASTER INPUT jacks and engage the

STEREO/MONO switch. Set the overall input level with the MASTER CONTROL, and use the CHANNEL LEVEL

controls for individual headphone levels.

Use the separate stereo IN jacks when driving a pair of headphones with different program material than what is on the

MASTER INPUTS. Connecting a plug into these jacks automatically disconnects that Channel from the Master Input

program material.

Never connect anything except a Rane power supply to the thing that looks like a telephone jack on the rear of the

unit. This is an AC input and requires special attention if you do not have a power supply exactly like the one originally

packed with your unit. See the full explanation of the power supply requirements elsewhere in this manual.

HC 6 CONNECTION

When first connecting the HC 6 to other components,

leave the power supply for last. This gives you a chance to

make mistakes and correct them without damage.

1. With the power switch in the off position, plug the power

supply line cord into the appropriate AC power source

indicated on the rear panel. Locate the power supply away

from the HC 6 and other hum sensitive equipment.

2. Plug the outputs from a mono or stereo source into the

MASTER INPUTS. For unbalanced systems use a standard

¼" mono patch cord. For balanced operation, use a stereo

¼" TRS connector with pin 2 (+) wired to the Tip; pin 3 (–)

wired to the Ring; and pin 1 (ground) wired to the Sleeve.

Please consult Rane Note 110 (enclosed) for additional

wiring arrangements.

3. When rack mounting the HC 6, you may wish to perma-

nently wire the rear headphone Outputs to remote jack

locations, such as in walls of a studio or other rooms. Use

the front panel Outputs for local or control room monitoring.

4. You might also consider wiring the six direct stereo INs

permanently to a patch bay or monitor mixer, but only if

you do not plan to use the MASTER INPUTS as well.

Whenever a plug is inserted into any individual stereo IN,

the MASTER INPUTS are bypassed for that particular

Channel. So for maximum flexibility, it is suggested that

only the MASTER INPUTs be permanently wired and that

the direct stereo INs be patched as necessary during regular

use.

5. The HC 6 may be installed into any rack which utilizes EIA

standard mounting hole spaces. The front panel of the HC

6 is heavy gauge steel, which adequately supports the unit.

For portable rack mounting, where extreme vibration and/

or shock is anticipated, it is recommended that the rear of

the HC 6, along with any other heavy product in the rack,

be stabilized to prevent possible damage to the chassis

should the rack be dropped, beamed up, or spindled.

WEAR PARTS: This product contains no wear parts.

Manual-2

FRONT PANEL DESCRIPTION

햲 POWER switch. Your basic, straightforward power switch. When the yellow LED is lit, the HC 6 is ready to go.

햳 Front panel PHONE Output jacks are in parallel with the rear panel stereo Output jacks. Use them to monitor any of the

six Channels for level or mix adjustments, or for easy access when the HC 6 is rack mounted. Plugging into these front jacks

does not disengage the rear Outputs.

햴 Individual LEVEL controls set the volume for each set of headphones, regardless of whether they are driven from the

MASTER INPUTS or from the direct stereo INs. When using the front and rear panel headphone jacks together, this control

varies the level of each headphone simultaneously.

햵 SIGNAL PRESENT indicators light (green) with any input signal above -20 dBu. See OPERATING INSTRUCTIONS

(on page Manual-4) for additional details.

햶 STEREO/MONO switch converts the MASTER INPUTS from stereo to mono so that a single input cable drives both sides

of the headphones.

햷 MASTER CONTROL sets the volume simultaneously to all headphones driven from the MASTER INPUTS. This does not

alter the volume on any headphones driven from the direct stereo INs.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	HC 6

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane HC 6 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Ibiza Sound MX401 Manual

14 September 2025

Mackie 1642VLZ4 Manual

14 September 2025

Mackie ProFX10v3+ Manual

14 September 2025

Mackie Master Fader Control App Manual

14 September 2025

Mackie DL32S Manual

14 September 2025

Mackie 1402VLZ4 Manual

14 September 2025

Mackie Onyx 12 Manual

14 September 2025

Mackie ProFX12v3 Manual

14 September 2025

Mackie 1604VLZ4 Manual

14 September 2025

Mackie Pro FX30 v3 Manual

14 September 2025