Theben AMUN 716 Manual

Theben Ikke kategoriseret AMUN 716

Læs gratis den danske manual til Theben AMUN 716 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 81 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 41 anmeldelser. Har du et spørgsmål om Theben AMUN 716, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
309 289
4. Installation
AMUN 716
CO2sensor
716 9 200
3.Characteristics
1. Designated use
t
The sensor serves to detect carbon dioxide (CO
2), relative humidity
and temperature in a variety of rooms (offices, schools, meeting
rooms etc). The CO2content of the air is a verifiable indicator of
the air quality in the living area. The higher the CO2 content, the
poorer the air. The devices are suitable for use in a normal environ-
ment.
• The CO2gas makes up only approx. 0.034 %
of our fresh air and acts as an indicator for assessing the
air quality in a room.
• The concentration of 0.1 % (1000 ppm) is the limit value for
indoor rooms.
• The maximum concentration in a workplace is 5000 ppm.
Composition of fresh air
2. Safety
The regulations and instructions in the ZVEI/ ZVEH Handbook must
be observed to ensure that the bus lines are installed and the units
are commissioned in a professional manner.
Tampering with or making modifications to the device will invali-
date the warranty.
• Do not use the sensor for safety related gas measurements!
•Only operate the sensor with extra-low voltage!
• Do not drop the sensor. Strong vibrations interfere with the
accurate measurement of CO2.
• Locate the (for temperature measurement) on an sensor
internal wall, at about eye level.
• Avoid drafts or heat emission.
• Do not not mount the sensor on a soft surface
as this will inhibit air exchange.
Thresholds of different readings
5. Description and function
The sensor has 2 LEDs that indicate the current CO
2content of the
measured ambient air and the humidity.
• Temperature detection range: 0–40 °C
• Setting range thresholds: 500-2550 ppm
• “Physical value” object: 0–9999 ppm
• “Relative humidity” detection range: 1 %–100 %
• There are 3 independent thresholds of the readings for CO
2and
relative humidity as well as a threshold for the temperature
reading.
• Exceeding or under-running the thresholds triggers a
response: Send priority. Switching, value.
• Every threshold has a disable object.
Danger of death through electric shock or fire!
Installation should only be carried out by pro-
fessional electrician!
WARNING
Gas Percentage volume
Nitrogen N278,08 %
Oxygen O220,95 %
Argon Ar 0,93 %
Carbon dioxide CO2340 ppm
LED for indicating CO2content
(from green red)
LED for indicating relative humidity
(from yellow blue)
Reading
below threshold
1
between thres-
hold 1 and 2
between thres-
hold 2 and 3
above
threshold 3
Humidity sta-
tus
humidify
humidity OK
dehumidify
conden-
sation alarm
LED CO2
green
yellow
orange
red
CO2concen-
tration
low
average
high
very high
LED relative
humidity
yellow
green
red
blue
Operating voltage: Bus voltage
Current consumption KNX: max. 12 mA
Bus interface module (BCU): integrated
Permissible ambient temperature: –5 °C to +45 °C
Protection class: III
Protection rating: IP 20 in accordance with
EN 60529
Equipment standard: in accordance with
EN 60730-1
Housing: 74 x 74 x 28 mm
9. Technical data
Observe deviating technical data on the rating plate! Technical
changes reserved. The devices comply with European Directives
73/23/EEC (low-voltage directives) and 89/336/EEC (EMC
Directives).
If the devices are combined with others for use within a system,
ensure that the system as a whole does not cause radio interfe-
rence.
The ETS database can be found under www.theben.de
Please refer to the Handbook for detailed functional descriptions.
Please refer to the Product Handbook for detailed functional des-
criptions (also at www.theben.de).
Theben AG
Hohenbergstr. 32
72401 Haigerloch
GERMANY
Phone +49 (0) 74 74/6 92 0
Fax +49 (0) 74 74/6 92-150
Service
Phone +49 (0) 74 74/6 92 -369
Fax +49 (0) 74 74/6 92-207
hotline@theben.de
Addresses, telephone numbers etc. at
www.theben.de
7. Programming physical address
8. Start-up
1. Press the program button (2) with a screwdriver through the
openings at the bottom of the device.
Programming LED (1) lights up.
AMUN 716 is in programming mode.
Start-up, diagnostics and configuration are handled by ETS
(KNX Tool Software).
Bus terminal and bus line
1. Open the housing cover with a screwdriver at the 4 side
lugs and feed the bus line from below through the opening.
2. Plug bus line into bus terminals.
Ensure correct polarity.
3. Close housing cover.
6. Bus connection
Don´t touch the membrane
while mounting the device
1
2

Produkt Specifikationer

Mærke: Theben
Kategori: Ikke kategoriseret
Model: AMUN 716

Har du brug for hjælp?

Hvis du har brug for hjælp til Theben AMUN 716 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Theben Manualer

Theben

Theben LUXORliving T4 S RF Manual

4 August 2025
Theben

Theben TA 8 S KNX Manual

3 August 2025
Theben

Theben BM 12 T KNX Manual

3 August 2025
Theben

Theben LUXORliving D1 DALI Manual

3 August 2025
Theben

Theben LUXORliving D1 S RF Manual

3 August 2025
Theben

Theben PlanoSpot 360 DALI-2 S DE Manual

3 August 2025
Theben

Theben RM 8 T KNX Manual

3 August 2025
Theben

Theben LUXORliving D1 DALI S RF Manual

3 August 2025
Theben

Theben LUXORliving J1 Manual

3 August 2025
Theben

Theben JU 1 KNX Manual

2 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

SereneLife

SereneLife SLCPTBPVC12 Manual

19 Oktober 2025
ResMed

ResMed Narval CC Manual

19 Oktober 2025
Dormakaba

Dormakaba CenTran 4 Manual

19 Oktober 2025
ResMed

ResMed AirFit N10 Manual

19 Oktober 2025
CRUX

CRUX SWRCR-59LV Manual

19 Oktober 2025
Dormakaba

Dormakaba Crane S1 Manual

19 Oktober 2025
Shape

Shape BP8000 Manual

19 Oktober 2025
Shape

Shape ALPKIT Manual

19 Oktober 2025
Shape

Shape COMPOFIC Manual

19 Oktober 2025
ResMed

ResMed AirFit F10 Manual

18 Oktober 2025